Slope & Drainage Conversion Chart
Convert inches of fall per foot to percent grade and approximate ratio.
Key takeaways
- These are mathematical conversions of uniform slope. They do not establish what slope a particular slab, accessible route, drain, or pavement should have.
- Required slope is project-specific. Accessibility, drainage capacity, doorway transitions, floor flatness, and vehicle operation can impose competing constraints.
- Treat these tables as field-reference and planning aids. Project drawings, specifications, current standards, manufacturer data, and local requirements govern when they differ.
| Fall | Percent grade | Approx. ratio |
|---|---|---|
| 1/16 in./ft | 0.52% | 1:192 |
| 1/8 in./ft | 1.04% | 1:96 |
| 3/16 in./ft | 1.56% | 1:64 |
| 1/4 in./ft | 2.08% | 1:48 |
| 3/8 in./ft | 3.13% | 1:32 |
| 1/2 in./ft | 4.17% | 1:24 |
| 3/4 in./ft | 6.25% | 1:16 |
| 1 in./ft | 8.33% | 1:12 |
How to read this table
These are mathematical conversions of uniform slope. They do not establish what slope a particular slab, accessible route, drain, or pavement should have.
Where it is useful
Use the chart to communicate grade between plans, forms, laser checks, and field crews that prefer different units.
Limitations
Required slope is project-specific. Accessibility, drainage capacity, doorway transitions, floor flatness, and vehicle operation can impose competing constraints.
How to apply this reference
Use the table to translate between inches per foot, percent and ratio during layout.
Accessibility criteria and drainage intent must be checked separately; a mathematically correct slope can still drain the wrong direction.
For slope & drainage conversion chart, write down the project-specific value that controls and use the table only to interpret or convert information. This keeps a quick-reference chart from quietly becoming a substitute specification.
Field documentation tip
When a value from this table influences an order, inspection or repair decision, record the source input and the project document or manufacturer information that authorized the decision. That makes the field record auditable if conditions or requirements change. On the Slope & Drainage Conversion Chart page, apply this point specifically to the conditions and records described above.
Example field use
A good way to use slope & drainage conversion chart is to start with a known project condition and use the table to translate or organize it—not to select an unknown requirement. For example, the first rows of this reference include 1/16 in./ft / 0.52%; 1/8 in./ft / 1.04%; 3/16 in./ft / 1.56%. Those entries are useful only after you know which row applies to the concrete, reinforcement, test, product or geometry you actually have.
When a table contains a typical range, planning factor or example value, write that label into your notes. If the project documents later provide a different value, replace the planning value rather than averaging the two. This is especially important for strength, air, cover, jointing, weather, testing and repair decisions where a quick field reference can look more authoritative than it really is. On the Slope & Drainage Conversion Chart page, apply this point specifically to the conditions and records described above.
What to verify before acting on the table
Before using slope & drainage conversion chart to support a material order or field decision, verify the units, edition/source where relevant, exposure or service condition, and whether the value is mandatory or illustrative. If the table points to an ASTM test, use the current procedure and trained testing personnel. If it touches structural design or reinforcement, use the approved drawings and governing code. If it concerns a proprietary repair, coating or curing product, the manufacturer's current technical data governs application details.
Keep the reference useful by pairing it with a field observation. A measured dimension, actual batch ticket, photograph, test report or marked-up pour plan gives the table context and makes later troubleshooting far more reliable. On the Slope & Drainage Conversion Chart page, apply this point specifically to the conditions and records described above.
Field checklist
- Confirm the table applies to the material or operation being reviewed.
- Verify units before using a value.
- Check the project documents for a controlling requirement.
- Use the current edition of any cited standard for formal work.
Common mistakes to avoid
- Copying a planning value into a specification without engineering or code review.
- Using a table without checking units or exposure conditions.
- Assuming a typical value is a universal minimum or maximum.
When project-specific review is needed
Use a qualified engineer, local code official, testing professional, concrete producer, or product manufacturer when the decision affects structural capacity, public safety, regulated work, unusual soil or environmental exposure, post-tensioning, heavy equipment, significant distress, or a requirement shown on the project documents. Rules of thumb are useful for planning only when they are clearly identified as such.
References & further reading
These links identify the primary organizations and documents used to frame this article. Project documents and the full current standard control where applicable.
- American Concrete Institute — Primary industry source for concrete codes, specifications, guides, and educational resources.
- ASTM Cement and Concrete Standards — Primary catalog for current concrete test methods and material standards.
- ACI SPEC-301-20 — Specifications for Concrete Construction — Reference specification used when incorporated into project specifications.